SECURITY SYSTEM INSTRUCTIONS

DSC-832/5010


1. ARMING ERROR

An error tone will sound if the system is unable to arm.  This will happen in the system is not ready to arm, (a door is open or movement in front of a motion detector) or if an incorrect user code has been entered.  If this happens press the (#) and try again. 


NOTE: Any time you press the * and any other number you will need to press the # to return to normal operation.  Also if an error is made when entering your code press the # to clear it out and return to normal.  If the keypad is beeping press the # to silence.  


2. BYPASS

To bypass any zone press *1 then the two digit zone number then #.

(example: *1 01 #, to bypass zone 1)

The bypass indicator should remain on. After you arm and disarm the system the bypass will clear.


3. CHIME

Press and hold the CHIME button to turn the Chime on and off.


4. CODES (example: *5 - master code - 01- new code - #)

Press * then 5, then your master code, then the two digit number of the user number that you wish to add or change.

Then enter the new 4 digit code, then #.

There are 6 user codes available and the master code is in position 40.  (To change the master code press *5 current code, then 1.


5. DISARMING ERROR

If you enter an incorrect code the system will not disarm, press the (#) and enter the correct code.


4. FALSE ALARM

If the alarm was accidental, enter your Access Code to silence the alarm, then call your monitoring station to avoid a dispatch.


5. INSTANT ARM

Press * then 9 and enter your code to arm the system without any entry delay time. NOTE:  This has no effect on the exit time delay.  (When using the *9 Instant arm you will still have whatever exit time to leave, but there will not be any entry time delay.)


6. MEMORY

When an alarm occurs the Memory indicator will turn on.  To view which zone caused the alarm press the * then 3.  When finished press # to return to normal.

*If you have an LCD keypad use the < > arrows to view the sensors in alarm memory.  To clear the memory, arm and disarm the system.


7. SMOKE DETECTOR RESET

Press and hold the RESET button on the right.


8. TROUBLE

When a trouble condition is detected the Trouble indicator will turn on and the keypad will beep every 10 seconds.  Press the # to silence the beeps. Press the * then 2 in order to view the trouble condition, each zone indicates a different problem.  Below are the trouble conditions by number which they will appear on the touch pad.

 LED/DIGIT TROUBLE CONDITION
 WHAT TO DO
1
If the number 1 shows press 1 and if 1 still shows, then the stand by battery is low
Call for service or replace the back up battery in the main control box
 2 NO AC POWER
Check your fuse box or circuit breakers; call for service if the trouble cannot be corrected.
 3PHONE LINE TROUBLE
This condition will be cleared when the trouble on the telephone line is corrected.  If this trouble does not clear itself automatically call for service
 4 FAILURE TO COMMUNICATE
This trouble will be cleared if the system again tries to call the monitoring station and is able to complete the call.  If this trouble does not clear itself automatically, call for service.
 5 ZONE FAULT
 Call for service.
 6 ZONE TAMPER
 Call for service.
 7 ZONE LOW BATTERY
Call for service or change the battery in the wireless sensor being reported.
 8 LOSS OF TIME AND DATE
 See below User Functions/ Time and Date

Press # to return to normal 


9. USER FUNCTIONS/TIME AND DATE

(example: *6 - master code - 1 - HH-MM-MM-DD-YY - #)

Press the * then 6, enter the master code, press 1 then the time;  HOURS, MINUTES, MONTH, DAY and YEAR.  Then #.  Time should be entered in Military format.   EXAMPLE:  *6 master code -1-10-05-03-01-06 - #  (10:05 am March 01, 2006) for 10:05 PM enter 22-05-03-01-06)

**If you have the LCD touch pad, press the * then 6, enter your master code then use the < > to TIME AND DATE.  Press * to select then change the time.  Press # to return to normal.